RMI
Inspection Trip Results Report
Al
Davis 5/23/2000
P/N 89-NOAO-4200-1001 S/N 001 (CaF2) CX – Plano
Pre Inspection
Post Inspection
Surface-A Good Good
Surface-B Good Good
Outer Diameter 5.8985” * S/B 5.9055” +/- .0039”
Central Thickness .6080 S/B .5906” +/- .0276”
Bevels Good Good
Note 11—Mark “EW” Note 11 will be done after coating
Note 12—Mark “ARROW” Note 12 will be done after coating
B to D—Measure run out of A .00010”
Test Plate—Radii-A 271.3562”Avg. S/B 271.0236” +/- 1.9685”
Irregularity 1/8 Wave
Fit of Test Plate to Lens 2-3/4 rings of CC power. Irregularity less than .250 P.V.
Radii-B Infinity and 3 rings of CX power. S/B +/- 10 fringes from infinity
(see attached photo)
*Outer diameter measurement is below the tolerance. Blanks were received in under size and accepted by NOAO.
P/N 89-NOAO-4200-1001 S/N 002 (CaF2) CX – Plano
Pre Inspection
Post Inspection
Surface-A Good Good
Surface-B Good Good
Outer Diameter 5.8980” * S/B 5.9055” +/- .0039”
Central Thickness .6140 S/B .5906” +/- .0276”
Bevels Good Good
Note 11—Mark “EW” Note 11 will be done after coating
Note 12—Mark “ARROW” Note 12 will be done after coating
B to D—Measure run out of A .00025” S/B .0004” or less
Test Plate—Radii-A 271.3562”Avg. S/B 271.0236” +/- 1.9685”
Irregularity 1/8 Wave
Fit of Test Plate to Lens 1-1/4 rings of CX power. Irregularity less than .250 P.V.
Radii-B 1-1/8 rings of CX power. S/B +/- 10 fringes from Infinity
Irregularity
.194 P.V. (see attached photo)
*Outer diameter measurement is below the tolerance. Blanks were received in under size and accepted by NOAO.
P/N 89-NOAO-4200-1001 S/N 003 (CaF2) CX – Plano
Pre Inspection
Post Inspection
Surface-A Good Good
Surface-B Good Good
Outer Diameter 5.8995” * S/B 5.9055” +/- .0039”
Central Thickness .6127 S/B .5906” +/- .0276”
Bevels Good Good
Note 11—Mark “EW” Note 11 will be done after coating
Note 12—Mark “ARROW” Note 12 will be done after coating
B to D—Measure run out of A .00010” S/B .0004” or less
Test Plate—Radii-A 271.3562”Avg. S/B 271.0236” +/- 1.9685”
Irregularity 1/8 Wave
Fit of Test Plate to Lens 1-1/4 rings of CC power. Irregularity less than .250 P.V.
Radii-B Infinity with 1-3/4 CC power. S/B +/- 10 fringes from Infinity
Irregularity
.179 P.V. (see attached photo)
*Outer diameter measurement is below the tolerance. Blanks were received in under size and accepted by NOAO.
P/N 89-NOAO-4200-1001 S/N 004 (CaF2) CX – Plano
Pre Inspection
Post Inspection
Surface-A Good Good
Surface-B Good Good
Outer Diameter 5.8990” */** S/B 5.9055” +/- .0039”
Central Thickness .6152” S/B .5906” +/- .0276”
Bevels Good Good
Note 11—Mark “EW” Note 11 will be done after coating
Note 12—Mark “ARROW” Note 12 will be done after coating
B to D—Measure run out of A .00010” S/B .0004” or less
Test Plate—Radii-A 271.3562”Avg. S/B 271.0236” +/- 1.9685”
Irregularity 1/8 Wave
Fit of Test Plate to Lens 2 rings of CX power. Irregularity less than .250 P.V.
Radii-B Infinity plus 3/4 of a wave CX power. S/B +/- 10 fringes from Infinity
Irregularity
.147 P.V. (see attached photo)
*Outer diameter measurement is below the tolerance. Blanks were received in under size and accepted by NOAO.
**Outer Diameter has some scratches.
P/N 89-NOAO-4200-1020 (SF6) CC - CX
Pre Inspection
Post Inspection
Surface-A Good Good
Surface-B Good Good
Outer Diameter 5.9455” S/B 5.9449” +/- .0031”
Central Thickness .6259” S/B .6114” +/- .0197”
Bevels Good Good
Annulus to Vertex .9460” S/B .9457” +/- .0039”
Note 10—Mark “SB2” Note 10 will be done after coating
B to D—Measure run out of A .00020” S/B .0004” or less
B to D—Measure run out of C .00010” S/B .0004” or less
Radii-A 12.0255”CC S/B 12.0260” +/- .0016”
Irregularity .169 P.V. (see attached photo)
Test Plate—Radii-B 43.7883” CX S/B 43.7776” +/- .0551”
Irregularity
.074 P.V. (see attached photo)
Fit of Test Plate to Lens 3 rings of CC power. Irregularity less than .250 P.V.
P/N 89-NOAO-4200-1022 (BaF2) CX - CC
Pre Inspection
Post Inspection
Surface-A Good Good
Surface-B Good Good
Outer Diameter 3.8470” S/B 3.8583” +/- .0039”
Central Thickness 1.1834” S/B 1.1846” +/- .0008”
Bevels Good Good
Vertex to Annulus 1.7338” S/B 1.7331” +/- .0039”
Note 11—Mark “SB4” Note 11 will be done after coating
A to D—Runout of B .00020” S/B .0004” or less
A to D—Runout of C .00020” S/B .0004” or less
Radii-A 4.3056”CX S/B 4.3067” +/- .0016”
Irregularity Less than .250 (see attached photo)
Radii-B 2.4232” CC S/B 2.4232” +/- .0039”
Irregularity .187 P.V. (see attached photo) S/B .250 P.V. or better
P/N 89-NOAO-4200-1024 (SF6) CC - CX
Pre Inspection
Post Inspection
Surface-A Good Good
Surface-B Good Good
Outer Diameter 5.6295” S/B 5.6299” +/- .0031”
Central Thickness .4262” S/B .4339” +/- .0079”
Bevels Good Good
Vertex to Annulus .5279” S/B .5323” +/- .0039”
Note 11—Mark “LB2” Note 11 will be done after coating
B to D—Runout of C .00020” S/B .0004” or less
B to D—Runout of A .00005” S/B .0004” or less
Radii-A 35.9570”CC S/B 35.9575” +/- .0157”
Irregularity .196 P.V. (see attached photo)
Test Plate Radii-B 81.375” CX S/B 81.3780” +/- .0787”
Irregularity Less than .250 P.V. S/B .250 P.V. or better
Fit of Test Plate to Lens 3 rings of CC power. Irregularity less than .250 P.V.
P/N 89-NOAO-4200-1025 (CaF2) CC - CX
Pre Inspection
Post Inspection
Surface-A Good Good
Surface-B Good Good
Outer Diameter 2.7564” S/B 2.7559” +/- .0031”
Central Thickness .6353” S/B .6319” +/- .0039”
Bevels Good Good
Annulus to Vertex .8337”* S/B .8280” +/- .0039”
Note 11—Mark “LB3” Note 11 will be done after coating
B to D—Measure run out of A .00020” S/B .0004” or less
B to D—Measure run out of C .00015” S/B .0004” or less
Radii-A 3.8976”CC S/B 3.8976” +/- .0012”
Irregularity .096 P.V. (see attached photo)
Test Plate -- Radii-B 4.1488” CX S/B 4.1488” +/- .0012”
Irregularity Less than .250 P.V. (see attached photo)
*Annulus to Vertex was over
tolerance by .0018”
P/N 89-NOAO-4200-1027 (CaF2) CC - CC
Pre Inspection
Post Inspection
Surface-A Good Good
Surface-B Good* Good
Outer Diameter 6.4982” S/B 6.4961” +/- .0032”
Central Thickness .5962” S/B .5925” +/- .0039”
Bevels Good Good
Vertex to Annulus 1.0004”** S/B .9956” +/- .0039”
Note 11—Mark “SR2” Note 11 will be done after coating
B to D—Measure run out of A .00020” S/B .0004” or less
B to D—Measure run out of C .00020” S/B .0004” or less
Radii-A 12.0493”CC S/B 12.0492” +/- .0039”
Irregularity .191 P.V. (see attached photo)
Radii-B 73.0323” CC S/B 73.0020” +/- .1969”
Irregularity .134 P.V. (see attached photo)
*Dimensions of large stoned
out chip (see attached sheet)
**Vertex to Annulus over tolerance
by .0009”
P/N 89-NOAO-4200-1030 (CaF2) CX - CC
Pre Inspection
Post Inspection
Surface-A Good Good
Surface-B Good Good
Outer Diameter 6.0265” S/B 6.0236” +/- .0031”
Central Thickness .4780”* S/B .4740” +/- .0039”
Bevels Good Good
Vertex to Annulus .7871”** S/B .7819” +/- .0039”
Note 11—Mark “LR1” Note 11 will be done after coating
A to D—Measure run out of C .00040” S/B .0004” or less
A to D—Measure run out of B .00025” S/B .0004” or less
Test Plate -- Radii-A 28.0000”CX S/B 28.0000” +/- .0394”
Irregularity
.100 P.V. (see attached photo)
Fit of Test Plate to Lens 7 rings of CX power S/B less than 18 rings +/-
Irregularity Less than .250 P.V.
Radii-B 12.7772” CC S/B 12.7783” +/- .0035”
Irregularity .170 P.V. (see attached photo)
*Central Thickness was over
tolerance by .0001”
**Vertex to Annulus was over
tolerance by .0013”
S/N 89-NOAO-4200-1031 (BaF2) CX - CX
Pre Inspection
Post Inspection
Surface-A Good Good
Surface-B Good* Good
Outer Diameter 5.5895” S/B 5.5906” +/- .0031”
Central Thickness .7520” S/B .7504” +/- .0039”
Bevels Good
Note 11—Mark “LR2” Note 11 will be done after coating
A to D—Measure run out of B .00025” S/B .0004” or less
Radii-A 13.6255”CX S/B 13.6276” +/- .0047”
Irregularity
Less than ¼ wave (see attached photos)
Test Plate -- Radii-B &